How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
Everybody has got their personal piece of advice about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably hard task. If the old tub is readily accessible, the task can relocate easily; if you need to open a wall to remove the old tub as well as place the brand-new bath tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will require an assistant to vacate the old bathtub as well as embeded in the brand-new one. See to it you have actually certified on your own for the work and also are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed job, it is much better to think about using one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will assist you set up a new tub in your restroom if you have already purchased a new tub and do not require to transform the setup of your previous water pipes.
Your tools and material checklist must make up the following:
Preparing for the Installment
To start with, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps device to stop stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is disconnect the water system. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be rather bothersome due to the limited accessibility that is commonly the case.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning throughout this process. Once the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Using the two wood boards under its feet, position the bath tub in the required position. The wooden boards are practical in equally spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small points.
The following objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the tub until the spirit level reviews degree.
To set up taps, fit the bottom of the outermost adaptable faucet port to the suitable supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water and examine all joints and also new pipework for leaks and also tighten them if needed. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and also sealing around the bathtub must wait up until the bathtub has actually been utilized at least once as this will resolve it right into its final placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washers are in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer provided backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, creating the water to penetrate the wall in between the bathroom and the tiling, causing issues with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and fittings. They are marketed in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill the bathtub with water before securing, to permit the activity experienced when the tub is in use. The sealer can split fairly early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently offered on the marketplace. It is a good idea to fit the ceramic tiles making use of waterproof or water-proof glue and also cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
As a keen reader on How to Install a Bathtub Yourself, I imagined sharing that excerpt was important. So long as you enjoyed our page plz make sure you remember to share it. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Additional Information
Report this page